Vehicles
171 not categorized PORSCHE 944S CONTROL ARMSCan't find what you need? Try browsing the Accessories or Exploded Diagrams!<-- Try narrowing by car using the menu to the left.FVD33150003 Rear toe control arms - order in pairs only restore proper suspension geometry with this adjustable lower rear control arm. The factory control arm can't compensate enough when lowering your Porsche, leaving you stuck with as much as ½ of toe in. The result is poor handling and rapid tire wear. This kit will provide the additional adjustment needed. The adjusting link has a left and right hand thread on each end. Rotating the link will increase or decrease the overall length of the arm. A precision teflon lined spherical rod end replaces the compliant rubber factory bushing for improved suspension response and feedback, and also reduces toe changes during acceleration and deceleration.
$218.90
Make a selection FVD34101707AT By ordering this article number, you will receive a reconditioned wishbone with newly pressed-in bearings. The calculated replacement deposit will be returned to you as soon as the old part has been received and checked. The reconditioning process includes full inspection of each track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our OEM front control arm bushings, part # FVD341999r. They are made with 65 shore rubber like the original control arms. If your old part is not repairable we will inform you immediately. General Fitment911 1989-94
From $418.00
Make a selection ER2290000 Diy kit - front control arm rubber bushings are now available as a kit for self-installation. in addition to a complete set of 4 OEM spec rubber bushings, the kit includes proprietary installation tools and instructions, which are essential for successful installation. use a pipe clamp or shop press to complete the install. General Fitment914 1970-76912 1965-69 911 1965-69 911 1970-73 911 1974-77 930 1975-77 911 1978-83 911 1984-86 911 1987-89
$249.00
Make a selection FVD33150030 This kit is complete and includes a total of 8, 4 smaller and 4 larger for the rear control arms. Our weather sealed monoball cartridges are crafted in high carbon steel and 7075 t6 aircraft aluminum. They will positively locate the suspension arms so suspension motion is accurately repeated in every corner. Sold as a set of 8. 1 kit is necessary per car. Please note: noise may resonate inside the cabin during street use.
$746.90
Make a selection FVD34101702RAK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install our FVD race front control arm bushings. They are made with uniball bearings so suspension motion is accurately repeated in every corner. Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrange...(choose a part on the right to read more)
$438.90
Make a selection BBI9965010002 • provides additional rear toe adjustment
$875.00
Make a selection FVD34101802RAT We will send you a reconditioned control arm, kindly send back your old part, or core . The reconditioned control arm has been full inspected, disassembled, degreased and we have properly installed FVD race front control arm bushings. They are made with uniball bearings so suspension motion is accurately repeated in every corner please note: each control arm is remanufactured in Germany, so the lead times can vary. This part is sold on an exchange basis, as such an additional charge (a core deposit) will be added to the purchase price of the part. After receiving your new part, kindly send back your old part, or core . Once the core is returned to us and it has been inspected to ensure it is rebuild-able and re...(choose a part on the right to read more)
$440.00
Make a selection FVD34101807ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install our FVD clubsport front control arm bushings, part # FVD341999r. They are made with 85 shore rubber (like the rennsport model). Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can ...(choose a part on the right to read more)
$418.00
Make a selection FVD3419991 This is a cost effective alternative to buying new control arms. Replace worn-out original soft rubber (65 shore hardness value) control arm bushings with new bushings of the same rubber (65 shore hardness value). This bushing set is made in Germany, weather sealed, crafted in high carbon steel and 7075 t6 aircraft aluminum and includes a 65 shore hardness value cores. This is a front and rear bushing for the front lower control arm (wishbone). 2 sets are necessary per car.
$124.30
Make a selection FVD34101802AT By ordering this part number you get after previous sending in General Fitment911 1994-98
$417.56
Make a selection
$81.13
Make a selection FVD34105307R Replace worn-out original soft rubber (65 shore hardness value) control arm bushings with our FVD clubsport series. They are made of rubber that has an 85-shore hardness value, the same as the rs models. 85-shore is more durable, provides more positive suspension location and is quiet and more forgiving than a monoball upgrade. This bushing is made in Germany, weather sealed, crafted in high carbon steel and 7075 t6 aircraft aluminum and includes an 85-shore hardness value core. Sold individually. 2 are necessary per car. Please note: this does not include the lower control arm, the picture circled in red is just for reference. General Fitment911 GT3 2003-05911 TURBO/GT2 2001-05 911 1998-05 BOXSTER 1997-04
From $98.92
Make a selection FVD34102702ATK By ordering this part number you get after previous sending in your wishbone overhauled with new race-silent blocs back. The race-silent blocs (85 shore) give you more stable driving. Should it not be repairable, we will inform you immediately.
$279.40
Make a selection
$46.20
Make a selection FVD341999R Replace worn-out original soft rubber (65 shore hardness value) control arm bushings with our FVD clubsport series. They are made from rubber with a 85 shore hardness value which is the same as the rennsport models. 85 shore is more durable, provides more positive suspension location and is quiet and more forgiving than a monoball upgrade. This is the ideal upgrade for street and light track / clubsport use. This bushing set is made in Germany, weather sealed, crafted in high carbon steel and 7075 t6 aircraft aluminum and includes 85 shore hardness value cores. This is a front and rear bushing for the front lower control arm (wishbone). 2 sets are necessary per car.
$124.30
Make a selection S701041 Rennline adjustable control arm links solve both these problems. Manufactured from 6061 aluminum and feature a turnbuckle design that allows each arm to be lengthened or shortened as needed to restore proper suspension geometry on a lowered Porsche. The fk teflon-lined rod end bearings ensure precision handling and lock in your car's alignment settings, ensuring predictable cornering under all conditions. Unlike the competitors' product, rennline arms come with eccentric locks and new hardware so you can completely eliminate the factory setup, which is known to go out of adjustment under hard driving and ruin your car's alignment. Note: two required per car. General Fitment911 1998-05911 TURBO/GT2 2001-05 911 GT3 2003-05 911 2005-08 911 GT3 2007-11 CAYMAN 2006-08 BOXSTER 2005-08
$306.90
Make a selection S715012 Rennline adjustable control arm links solve both these problems. Manufactured from 6061 aluminum and feature a turnbuckle design that allows each arm to be lengthened or shortened as needed to restore proper suspension geometry on a lowered Porsche. The fk teflon-lined rod end bearings ensure precision handling and lock in your car’s alignment settings, ensuring predictable cornering under all conditions. Note: four required per car. General Fitment911 1998-05911 TURBO/GT2 2001-05 911 GT3 2003-05 911 2005-08 911 GT3 2007-11
$236.50
Make a selection S727374101 If you're serious about how your 993 handles, you should upgrade the rear suspension with adjustable control arm links. There are two major drawbacks to the factory links: 1) you can't lower your car and maintain proper suspension geometry. The factory links create too much toe-in, which cannot be adjusted out, creating handling problems and excessive tire wear. 2) the factory links have rubber bushings, which make handling imprecise, especially in performance driving when suspension loads are highest. General Fitment911 1994-98
$1,758.90
Make a selection FVD34105304BU1 Diese buchse ersetzt an ihrem vorderen querlenker die mittlere buchse. Es handelt sich bei dieser buchse um einen hartegrad von 85 shore wie original bei den rs -modellen ( GT3 rs, GT2 rs ) preis pro stuck, pro querlenker wird ein stuck benotigt.
$115.50
Make a selection S735012 If you're serious about how your 993 handles, you should upgrade the rear suspension with adjustable control arm links. There are two major drawbacks to the factory links: 1) you can't lower your car and maintain proper suspension geometry. The factory links create too much toe-in, which cannot be adjusted out, creating handling problems and excessive tire wear. 2) the factory links have rubber bushings, which make handling imprecise, especially in performance driving when suspension loads are highest. Rennline adjustable control arm links solve both these problems. Manufactured from 6061 aluminum and feature a turnbuckle design that allows each arm to be lengthened or shortened as needed to restore proper su...(choose a part on the right to read more) General Fitment911 1994-98
$306.90
Make a selection 90134104303 Known as: wishbone View/Change Diagram
From $321.44
Make a selection
$2,734.95
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |